lonawifabona 2 Posted June 20, 2017 (edited) Hello guys/girls. Just bought a mx83 cressida and also a 1jz vvti engine. Goals are to build a super cheap drift beater. Currently stripped the motor down todo big end and conrod bearings. Also piston rings. Found 2x valve steam seals leaking but everything else was in very good condition. Now while I wait to recieve some parts what parts should I keep in the cressida engine bay and what should i ditch, note this is a track car only. Any advice and help will be appriciated. Edited June 20, 2017 by lonawifabona Share this post Link to post Share on other sites
lonawifabona 2 Posted June 25, 2017 (edited) some bits have arrived. Main and connecting road shells, piston rings and also front and rear crank seals. honed the cylinders. cleaned the block and mating surfaces. Replaced all seals, rings and shells. re-assemlbed the bottom end back togeather. I completly stripped the head. removed steam seals and lapped in the valves. Here are some pictures of my build so far. Edited June 25, 2017 by lonawifabona Share this post Link to post Share on other sites
pmod 263 Posted June 26, 2017 Very nice! Grandpa drifting ftw. Going back to the question in your first post, there's really not much in a Cressida to ditch if you're changing the engine, as with the 7MGE out, there's no cruise control left and the giant intake setup will be gone. Personally, I'd change the BMC and lose the ABS unit (assuming it even had it), ditch the AC condensor and lines, ditch the bonnet insulation, midmount the intercooler under the radiator support and cut some extra intake holes in the bumper to avoid fitment issues, swap the giant charcoal cannister for a tiny one from another car, and that's about it. You'll probably want to add an oil cooler and a power steering cooler, unless you were keeping the stock radiator for some reason, in which case it should have a tranny cooler in the bottom iirc. Get a small battery and leave it in the front, then drop in the 1J in, cut/hammer your wheel tubs and do something with the knuckles for more lock. If the overheating issues with the MX83/MA70 are anything to go by, it would be worth cutting a rear bonnet vent for the rear cylinders to vent trapped heat, as well as install a fat radiator with decent thermo fans. Pretty standard stuff tbh. Gutting the interior should net you a lot of weight savings. Share this post Link to post Share on other sites
lonawifabona 2 Posted June 27, 2017 (edited) Thanks mate I'll make sure i do them things. Hopefully end of this week the head will be back on the block. Next on my todo list is to find some used 2jz injectors and figure out what turbo will be good to use goals are 250-280 kw any suggestions? Edited June 27, 2017 by lonawifabona Share this post Link to post Share on other sites
blingcommander 278 Posted June 27, 2017 High flow turbo will make that power. But if you want headroom for more go a kelway manifold,44mm gate and a kinugawa t67 25g 10cm. Not sure how you are going to get 2j injectors to fit as they are side feed. Vvti 1j is top feed. Share this post Link to post Share on other sites
lonawifabona 2 Posted June 27, 2017 For my power goals will it be cheaper and easier getting a stock ecu and using a piggy back system on it? Share this post Link to post Share on other sites
blingcommander 278 Posted June 27, 2017 Not teally. Simple and easy would be a power fc and a z32. Bit more but will get better results would be like a haltech ps1000 Share this post Link to post Share on other sites
lonawifabona 2 Posted July 11, 2017 (edited) Bit of an update. Spent my weekend stripping the interior and fitting a 1jz engine loom in. Here are some photos to show what I have done. Sorced out recently some engine mounts for the 1j. Trying to decide what clutch to get. purchased some drop in Denso 530cc injectors for a very cheap price. trying to source a power fc that is reasonable price. need to order in a 1jz-w58 bellhousing, fork and bearing carrier. Ill also be ordering a fuel cell, surge tank and some pumps soon. ( do i need to keep the charcoal canister?) Edited July 11, 2017 by lonawifabona Share this post Link to post Share on other sites
lonawifabona 2 Posted December 25, 2017 (edited) Well im back after ordering bits and pieces I have now received: One piece tail shaft New power fc Alloy radiator with thermos Intercooler with piping Clutch and fly wheel to suit a 1jz to w58 engine and gearbox mounts Also a custom made clutch pedal/master Will post photos up shortly off all parts Edited December 25, 2017 by lonawifabona Share this post Link to post Share on other sites
greentones 0 Posted December 27, 2017 (edited) I can't wait to see how it turns out! Edited December 28, 2017 by greentones Share this post Link to post Share on other sites